Cisco Firepower Threat Defense Software and Cisco FirePOWER Services TCP/IP Traffic with Snort 2 and Snort 3 Denial of Service Vulnerability – Source:sec.cloudapps.cisco.com

High

Summary

• A vulnerability in the TCP/IP traffic handling function of the Snort Detection Engine of Cisco Firepower Threat Defense (FTD) Software and Cisco FirePOWER Services could allow an unauthenticated, remote attacker to cause legitimate network traffic to be dropped, resulting in a denial of service (DoS) condition.

  This vulnerability is due to the improper handling of TCP/IP network traffic. An attacker could exploit this vulnerability by sending a large amount of TCP/IP network traffic through the affected device. A successful exploit could allow the attacker to cause the Cisco FTD device to drop network traffic, resulting in a DoS condition. The affected device must be rebooted to resolve the DoS condition.

  Cisco has released software updates that address this vulnerability. There are no workarounds that address this vulnerability.

  This advisory is available at the following link:
  https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-sa-ftd-snort-fw-BCJTZPMu

  This advisory is part of the October 2024 release of the Cisco ASA, FMC, and FTD Software Security Advisory Bundled Publication. For a complete list of the advisories and links to them, see Cisco Event Response: October 2024 Semiannual Cisco ASA, FMC, and FTD Software Security Advisory Bundled Publication.

Affected Products

• This vulnerability affects Cisco products if they are running a vulnerable release of Cisco FTD Software or Cisco FirePOWER Services and have either Snort 2 or Snort 3 enabled.

  For information about which Cisco software releases are vulnerable, see the Fixed Software section of this advisory.

  Determine the Snort Configuration on Cisco FTD Software

  On new installations of Cisco FTD Software releases 7.0.0 and later, Snort 3 is running by default. On devices that were running Cisco FTD Software Release 6.7.0 or earlier and were upgraded to Release 7.0.0 or later, Snort 2 is running by default.

  To determine if Snort is running on Cisco FTD Software, see Determine the Active Snort Version that Runs on Firepower Threat Defense (FTD). Snort 2 or Snort 3 must be active for this vulnerability to be exploited.

  Only products listed in the Vulnerable Products section of this advisory are known to be affected by this vulnerability.

  Cisco has confirmed that this vulnerability does not affect the following products:

  • Cisco Adaptive Security Appliance (ASA) Software
  • Cisco Secure Firewall Management Center (FMC) Software, formerly Firepower Management Center Software
  • Open Source Snort 2
  • Open Source Snort 3

Workarounds

• There are no workarounds that address this vulnerability.

Fixed Software

• Cisco has released free software updates that address the vulnerability described in this advisory. Customers with service contracts that entitle them to regular software updates should obtain security fixes through their usual update channels.

  Customers may only install and expect support for software versions and feature sets for which they have purchased a license. By installing, downloading, accessing, or otherwise using such software upgrades, customers agree to follow the terms of the Cisco software license:
  https://www.cisco.com/c/en/us/products/end-user-license-agreement.html

  Additionally, customers may only download software for which they have a valid license, procured from Cisco directly, or through a Cisco authorized reseller or partner. In most cases this will be a maintenance upgrade to software that was previously purchased. Free security software updates do not entitle customers to a new software license, additional software feature sets, or major revision upgrades.

  The Cisco Support and Downloads page on Cisco.com provides information about licensing and downloads. This page can also display customer device support coverage for customers who use the My Devices tool.

  When considering software upgrades, customers are advised to regularly consult the advisories for Cisco products, which are available from the Cisco Security Advisories page, to determine exposure and a complete upgrade solution.

  In all cases, customers should ensure that the devices to be upgraded contain sufficient memory and confirm that current hardware and software configurations will continue to be supported properly by the new release. If the information is not clear, customers are advised to contact the Cisco Technical Assistance Center (TAC) or their contracted maintenance providers.

  Customers Without Service Contracts

  Customers who purchase directly from Cisco but do not hold a Cisco service contract and customers who make purchases through third-party vendors but are unsuccessful in obtaining fixed software through their point of sale should obtain upgrades by contacting the Cisco TAC: https://www.cisco.com/c/en/us/support/web/tsd-cisco-worldwide-contacts.html

  Customers should have the product serial number available and be prepared to provide the URL of this advisory as evidence of entitlement to a free upgrade.

  Note: The Cisco Software Checker does not discriminate between Cisco FTD devices that are configured with Snort 2 and Snort 3. For the Cisco FTD Software code train 7.4, the Snort 3 fix is in Release 7.4.1 and the Snort 2 fix is in Release 7.4.2.

  Cisco ASA, FMC, and FTD Software

  To help customers determine their exposure to vulnerabilities in Cisco ASA, FMC, and FTD Software, Cisco provides the Cisco Software Checker. This tool identifies any Cisco security advisories that impact a specific software release and the earliest release that fixes the vulnerabilities that are described in each advisory (“First Fixed”). If applicable, the tool also returns the earliest release that fixes all the vulnerabilities that are described in all the advisories that the Software Checker identifies (“Combined First Fixed”).

  To use the tool, go to the Cisco Software Checker page and follow the instructions. Alternatively, use the following form to search for vulnerabilities that affect a specific software release. To use the form, follow these steps:

  1. Choose which advisories the tool will search-all advisories, only advisories with a Critical or High Security Impact Rating (SIR), or only this advisory.
  2. Choose the appropriate software.
  3. Choose the appropriate platform.
  4. Enter a release number-for example, 9.16.2.11 for Cisco ASA Software or 6.6.7 for Cisco FTD Software.
  5. Click Check.

  For instructions on upgrading a Cisco FTD device, see the appropriate Cisco FMC upgrade guide.

  Additional Resources

  For help determining the best Cisco ASA, FMC, or FTD Software release, see the following Recommended Releases documents. If a security advisory recommends a later release, Cisco recommends following the advisory guidance.

  Cisco ASA Compatibility
  Cisco Secure Firewall ASA Upgrade Guide
  Cisco Secure Firewall Threat Defense Compatibility Guide

Exploitation and Public Announcements

• The Cisco Product Security Incident Response Team (PSIRT) is not aware of any public announcements or malicious use of the vulnerability that is described in this advisory.

Source

• This vulnerability was found during the resolution of a Cisco TAC support case.

Cisco Security Vulnerability Policy

• To learn about Cisco security vulnerability disclosure policies and publications, see the Security Vulnerability Policy. This document also contains instructions for obtaining fixed software and receiving security vulnerability information from Cisco.

• Subscribe

Related to This Advisory

• Cisco Event Response: October 2024 Cisco ASA, FMC, and FTD Software Security Advisory Bundled Publication

URL

• https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-sa-ftd-snort-fw-BCJTZPMu

Revision History

• Version	Description	Section	Status	Date
  1.0	Initial public release.	–	Final	2024-OCT-23

  Show Less

Feedback

• Leave additional feedback